Showing all 17 results
This kit consists of:
4 – PRISM 120 SE LED Tube Light
1 – Hard Plastic Protective Case
1 – Custom EVA Plastic Foam
4 – AC Power Adapter with Regional Plug
4 – SE Rail Clamp + Set w/ 3/8″
4 – Mini Tripod Stand and Hand Grip
8 – 9. Solutions 5/8” Rod Set (500mm)
4 – T-Mount Hexagon System
8 – Battery Pack (4 additional Battery Packs)
1 – External Battery Charging Station
This kit consists of:
4 – PRISM 60 SE LED Tube Light
1 – Hard Plastic Protective Case
1 – Custom EVA Plastic Foam
4 – AC Power Adapter with Regional Plug
4 – SE Rail Clamp + Set w/ 3/8″
4 – Mini Tripod Stand and Hand Grip
8 – 9. Solutions 5/8” Rod Set (500mm)
4 – T-Mount Hexagon System
4 – Battery Pack (Included in each of the P60 SE lights)
1 – External Battery Charging Station
IN THE KIT
IN THE KIT
Aluminum Housing and Rotatable Metal End Caps
Prism SE LED tubes are built with a rugged AL6063+ aircraft-quality aluminum housing and metal end caps. Prism SE LED tubes can withstand travel and tough rental environments. This LED tube has a 180º rotating end cap that gives you the flexibility to keep the on-board menu out of sight for in-sight shots.
RGBWW Color Engine
The Prism SE has an RGBWW color engine, with one billion colors to mix and choose from!
RGBWW Color Engine
The Prism SE has an RGBWW color engine, with one billion colors to mix and choose from!
Special Effects
The Prism SE comes with standard built-in special effects, as well as the capacity for you to add up to five of your own custom effects.
The Poly Shell Fixture Housing PS402 is a long 4 – 4 feet long w/ 4 Bank w/ Power 4 Adaptor (Shell, Q-block sets & Mounting part) with improved 1.5mm aluminum sheet plate mounted on the front and back of the poly shell fixture.
One of the most outstanding features of the SGC PRISM and PRISM SE series is the ability to remove the internal battery from the fixture. The new External Battery Charging Station makes it possible to charge multiple batteries at a time outside the tube. This is incredibly convenient and important, because it allows filmmakers to swap their batteries while on set. This means that when one battery runs out of power, it can be pulled out of the tube and put into this external charger with 3 other batteries, totaling four batteries charging at the same time. A fully charged battery can then be put back into the tube, while the others are in the charging stand, which prevents expensive and painful delays.
These grids come in their own travel drawstring pouch. They are available in 2ft or 4ft LED tubes. Lightweight and sturdy, these grids are universally sized to fit SGC Lights or other comparable branded tube lights.
These grids come in their own travel drawstring pouch. They are available in 2ft or 4ft LED tubes. Lightweight and sturdy, these grids are universally sized to fit SGC Lights or other comparable branded tube lights.
REPLACEMENT BATTERY FOR PRISM AND PRISM SE TUBES
18.5V Replacement Battery Pack: 5 Cells of LG18650 @ 3200mAh = 59.2Wh / 16000mAh
Stackable mounting system for Hybrid and Prism tube lights. The system comes with 360 pin receiver and is compatible with the light stand and C-stand.
Stackable mounting system for Hybrid and Prism tube lights. The system comes with 360 pin receiver and is compatible with the light stand and C-stand.
This wire and adaptor set will get your Prism connected to a DMX Board with ease and efficiency. Larger sets or those with more complicated lighting effects will use wired DMX to control the lights on set. This setup allows you to connect your prism to a traditionally used DMX board.
The set includes:
1x Mini XLR to Mini XLR Wire
1x Mini XLR to RJ45 Ethernet Port Wire
1x RJ45 Ethernet Port to DMX 5-pin Adaptor
These rare earth neodymium Cup magnets are made for holding stuff & that is what they do best. Neodymium magnets are unique because of their extreme resistance to demagnetization and will only lose their magnetism if they’re heated above 176 degrees Fahrenheit.
Technical
– Magnets Provides 40 Pounds Of Holding Power
– Maximum Working Temperature 176 F (80 C)
– Material: Sintered Ndfeb Neodymium
– Rating: 14,800 Gauss Pulling Force
– Pole Orientation: Axially Magnetized, The Poles Are On The 1/2″ Thickness
– Coating: ni+Cu+Ni 3 Layer Plated
– Tolerance: All The Dimensions Are +/-0.002in With Coating
– These are not the magnets you played with as children 10-20 times the force of those old time magnets.
No products in the cart.